How to Replace a Kia Sportage Replacement Key
The key of many Kia models has a keyless entry system built into. This key is similar to a remote control and can be exchanged by a Kia dealer.
Key fobs can stop working due to a variety of reasons, such as an inactive battery, worn out buttons signal interference, or water damage. Here are some suggestions to help you get your Kia key fob that is a replacement for the sportage for good.
How do you replace the remote key or the smart key?
The battery inside your Kia's smart key will eventually require to be replaced, regardless of whether it is a remote key, a push-to-start key or a regular key that is not equipped with transponder. This is particularly true if your car displays a message telling you that the remote or smart keys are in poor condition.
It's a simple process. To replace the battery in the key fob take the mechanical key from the slit at the back of the key fob. Then pry open the cover. Inside the key fob, there will be an incredibly small screw that holds the battery in the correct position. With a small screwdriver, take the screw off and pull out the battery that was in place. Then insert the new one and close the slit inside the key fob.
Once the key fob has a fresh battery, test it by pressing the lock and unlock buttons. You're good to go If the doors lock and unlock as expected. You can now use Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to run some errands in Brandon.
Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a computer that is available only to the locksmith for cars or dealer. Other keys (non-transponder metal keys) do not require programming. If you're looking to reprogramme your key, you'll need write down the key code's number on the tag for the key code.
How do I replace a battery
If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is not fully charged. A low battery may cause other issues, such as the check engine light flashing or the engine not cranking correctly. Fortunately replacing kia spare key G28 is a simple DIY task that requires only a few tools.
Make sure to shut off your vehicle and shut all doors prior to beginning. Find the small metal or plastic piece near the bottom of the key fob. Then, jiggle it until the metal key is released. You can then insert the key in the handle of the door for the driver to unlock your car.
To replace the battery on the key fob remove the cover at the rear. Use a pry tool to loosen up the latch that holds the black negative cable. Take the old battery out, and then position the new battery to ensure that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.
After you have installed the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia's key fob to ensure it's functioning properly.
How do you replace the smart key
Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference is that the smart key has the small blade of a key tucked inside it, while the standard key fob does not. Both key fobs contain a battery that will eventually need to be changed. Fortunately, it's quite simple and only takes about two minutes.
Make sure you turn off your Kia and sit on a flat well-lit and well-lit area before you begin. Remember that the fob is made up of small parts that can be thrown off when you're not careful.
The release button for the small size is located on the lower backside. It could be a circular silver button or a rectangular slot. After pressing this button mechanical key blade, it will pop out and you can then open the key fob.
Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is one called CR-2032 and can be bought from a local or online auto parts store. When you're done, the key fob should permit you to lock and unlock your vehicle even if it's not running.
How do you replace a broken mechanical key
The Kia keyfob is a great convenience that allows us to lock or unlock our car by pressing the button. But like any device, it can have problems at times. There are steps that can be taken to fix these issues and keep our key fobs in good working condition in the long run.
One of the most frequently encountered problems is a dead or dead battery. This can cause the fob to stop working altogether or even to stop working intermittently. If this happens try replacing the battery with a fresh new one.
If this doesn't fix the problem you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one.
Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to check that it's functioning correctly. Contact a dealer, or a locksmith to resolve the problem when the fob still is not working. To avoid locking outs in the future, ensure that you have an emergency key that can work in all of the door and trunk cylinders.